background image

 

16

10. ACCESSORIES 

 

Stands 

Elegant stands are available for the Stratford Sf only. These increase the height of the appliance and rear flue 
outlet by approximately 125mm (6''). Check current brochure for details. 
 
 

Traceries 

For added decorative effect, beautiful Door Traceries (Arches, Dawn & Sunburst) are available for the complete 
Stratford fires range. 
 
 

Paint 

Matching aerosol paint to tone in any connecting flues, pipes or surrounding metalwork. 
 
 

Interchangeable Canopy 

Traditional canopy (Low) is available for the Stratford Si only. It is easy to fit and can always be added 
afterward. 
 
 

Add in Boilers 

(see fig 11)

 

A "slab" type add-in-boiler is available for the Stratford Sf only, which occupies the position of the rear firebox 
liner panel. 
Stratford Sf convector units can be fitted with "slab" type boilers only, not "cantilever" type. 
 
Fitting: 

 

Remove the fuel retainers, rear firebox liner panels and throat plate. 

 

Knock out the 2 blanking discs corresponding to the terminals on the boiler at the rear of the fire. 

 

Introduce the boiler to the appliance through the main fire door and locate the terminal pipes through the 
back plate holes and seal around boiler terminals with fire cement. 

 

Engage locking nuts to the thread of the terminals and tighten to secure the boiler in position, ready for 
connection to flow and return pipes. 

 

Replace, throat plate and fuel retainers. 

 

Note: On boilers the terminal which is approximately flush with the edge of the boiler and marked "TOP" 
must be fitted uppermost, to prevent "Kettling". 

 
For details of the outputs and sizes for your particular model please see Chart overleaf. 
 

Figure 11 

 

Summary of Contents for Stratford Sf 30



































Reviews: