background image

 

8

4. REFRACTORY LINING FOR S

CONVECTOR MODELS ONLY 

 
 

Warning: Refractory linings are very fragile, handle with extreme care. 

 

Stratford Sf Multifuel

 

Convectors

 are lined with reflective panels, consisting of a combination of rectangular 

linings, which sit on the rear ledge, and side linings which sit on the landings. A throat plate is sited above the 
grate, so shaped that it rests on steel guides and between the side linings. 
 
If the refractory linings have not been fitted to your appliance prior to despatch, they should be fitted as follows: 
 
 

Stratford Sf30 & Sf50

 (see Fig 3 & 4) 

 

 
 

 

Figure 3  

 

 

 

 

 

 

Figure 4 

 
 

 

Remove front fuel retainer bars. 

 

Set the two linings on the side ledges on either side of the firebox. 

 

Set the rectangular linings on the upper surface of the grate bar channel at the rear of the firebox. 

 

Fit the throat plate with the tab at the front marked "Throat plate" pointing down, with the projecting lugs on 
the sides of the throat plate resting on the top of the baffle landings and the bend at the back resting against 
the rear refractory lining 

 

Replace the front fuel retainer bars. 

 

Note: Neither the rear linings nor the side linings are "handed" and both faces are suitable for direct contact 
with the fire. 

 
 

Stratford Sf70 & Sf90 

(see Fig 5)

 

 

 

Figure 5 

 
 
 

SM70 Convector / SM90 Convector

SF30 CONVECTOR

SF50 CONVECTOR

Summary of Contents for Stratford Sf 30



































Reviews: