Aastra 9143i Series Administrator'S Manual Download | Manualshive

Page: 390 / 1140

background image

Operational Features

5-84

41-001160-04 Rev 02, Release 2.5

IP Phone Administrator Guide

Preferred Line and Preferred Line Timeout

An Administrator or User can define a

preferred line

as well as a

preferred

timeout

. If a preferred line is selected, after a call ends (incoming or outgoing),

the display switches back to the preferred line. Next time you go off-hook, you
pickup on the preferred line. You can specify the number of seconds it takes for
the phone to switch back to the preferred line using the “

preferred timeout

”

parameter.

An Administrator can configure the “

preferred line

” and the “

preferred

timeout

” parameters using the configuration files or the Aastra Web UI. A User

can configure these parameters using the Aastra Web UI only.

The following table provides the behavior of the preferred line focus feature with
other features on the phone.

Phone Feature

Preferred Line Behavior

call return

The phone switches back to the focused line immediately after
the call ends.

speeddial

The line is already specified when the speeddial is created. The
phone switches back immediately after the call ends.

conference

For incoming calls, the phone switches back immediately after
the call ends.

transfer

For incoming or outgoing calls, the current behavior is that the
same line used to transfer the call does not change. For incoming
calls, the phone switches back immediately after the call
transfers.

blf

The phone switches back immediately after the call ends.

park

The phone switches back immediately after the call ends.

voicemail

The phone switches back immediately after the call ends.

redial

The phone switches back immediately after the call ends.

dialing

For incomplete dialing on a non-preferred line, the focus does not
change if some digits are entered.
If no digits are entered or digits were cleared, the focus changes
to preferred line after the time out has passed without activities.

«
...
388
389
390
391
392
...
»

Summary of Contents for 9143i Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 9143i Series

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Brand: Krüger & Matz Pages: 20

Brand: Light Repute International Pages: 15

Brand: Polycom Pages: 2

Brand: Sonim Pages: 1

DIAL-ALERT AD-105 Guide

Brand: SkyLink Pages: 14

SMARTPHONE 3.2 LITE

Brand: Tesla Pages: 3

Brand: Avaya Pages: 84

Brand: Micromax Pages: 40

Brand: Kogan Pages: 22

Brand: Nebi.Mobi Pages: 21

Brand: Docomo Pages: 95

Brand: Pantech Pages: 213

Brand: Alcatel Pages: 21

Brand: PCD Pages: 16

Brand: Audiovox Pages: 49

Brand: Grandstream Networks Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands