Aastra 9143i Series Administrator'S Manual Download | Manualshive

Page: 455 / 1140

background image

Operational Features

41-001160-04 Rev 02, Release 2.5

5-149

Configuring Operational Features

Programmable Keys (9143i, 6730i, 6731i, 6753i, 6755i)

The following table provides the number of softkeys and programmable keys you
can configure, and the number of lines available for each type of phone.

*The M670i expansion module consists of 36 softkeys. You can have up to 3 expansion modules on an IP phone totaling
108 softkeys.

**On the 6753i, two of the 6 programmable keys are the DELETE and SAVE keys and can be programmed only if
Administrator allows.

Softkey/Programmable Key/Expansion Module Key Functions

You can configure the softkeys and programmable keys on the phones and any
attached expansion module keys to perform specific functions using the
configuration files or the Aastra Web UI. The following table identifies the
available functions of the softkeys, programmable keys, and expansion module
keys on the IP phones. Available functions may vary on each model phone.

The following

Key Functions Table

lists the available functions for the keys on

the IP Phones and Expansion Modules.

IP Phone

Model

Softkeys

Expansion Module

Keys

Programmable

Keys

Lines

Available

Handset

Keys

Available

9143i

-

Not Applicable

7

9

-

6730i

-

Not Applicable

8

6

-

6730i

-

Not Applicable

8

6

-

6753i

-

36 to 108*

(Model M670i)

6**

9

-

6755i

6

36 to 108*

(Model M670i)

60 to 180**

(Model M675i)

6

9

-

Note:

These functions apply to all model phones unless specifically

indicated that the function does not apply. The 6751i IP Phone does not
have programmable keys or softkeys.

«
...
453
454
455
456
457
...
»

Summary of Contents for 9143i Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 9143i Series

Brand: Haier Pages: 42

Brand: KARBONN Pages: 18

Brand: KARBONN Pages: 12

Brand: Kantronics Pages: 260

alcatel Pixi4-7 4G BELL

Brand: TCL Pages: 41

Brand: Yezz Pages: 68

Brand: Alcatel Pages: 58

Brand: NTT docomo Pages: 211

Brand: TCL Pages: 33

Brand: Pantech Pages: 60

Brand: i-mobile Pages: 39

Brand: Overmax Pages: 126

Brand: Cisco Pages: 194

Brand: LG Pages: 242

Brand: LG Pages: 307

Brand: Zte Pages: 46

Brand: Zte Pages: 142

Brand: Sanyo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands