Aastra 9143i Series Administrator'S Manual Download | Manualshive

Page: 491 / 1140

background image

Operational Features

41-001160-04 Rev 02, Release 2.5

5-185

Configuring Operational Features

Speeddial/Conference Key

(not applicable to the 6751i)

The IP Phones allow you to configure a softkey/programmable key/expansion
module key to be used as a speeddial conference key (

Speeddial/Conf

key) while

remaining in the current call. This key allows a user on a call, to conference
another party at a pre-defined number while remaining in the conference call.

For example, while on an active call, a user can use the Speeddial/Conf key to dial
a recording service and have the resulting conference recorded.

How it Works

If you configure a softkey/programmable key/expansion module as a

Speeddial/

Conf

key, and you press this key while on an active call, the focused line changes

to the dialing line. A

Cancel

softkey displays on the phone (only those phones

that have LCDs larger then 3 lines), allowing you to abort the conference
speeddial if required. The message "

Ringing

..." displays below the number when

the far end is ringing. The message "

Conf. Unavailable

" briefly displays when a

conference is already in progress or when the CT handset is in use. The active call
is not put on hold when the speeddial number is dialed.

Limitations for Speeddial/Conference Key

The following are limitations for the Speeddial/Conference key:

•

The CT handsets are not supported.

•

The feature is not compatible with centralized conferencing.

The softkey/programmable key is called "

Speeddial/Conf

" in the Web UI drop

down list. In the configuration file, use "

speeddialconf

" as the softkey type.

Note:

If currently in a conference, the Speeddial/Conf key is disabled on

the active call.

«
...
489
490
491
492
493
...
»

Summary of Contents for 9143i Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 9143i Series

Brand: T-Mobile Pages: 24

Brand: Olympia Pages: 88

Brand: Samsung Pages: 123

SCH-R350 Series

Brand: Samsung Pages: 140

Brand: Samsung Pages: 138

Brand: Samsung Pages: 150

Brand: Samsung Pages: 72

Brand: Samsung Pages: 326

SGH C417 - Cell Phone - AT&T

Brand: Samsung Pages: 114

Brand: Samsung Pages: 136

SCH-R730 series

Brand: Samsung Pages: 134

Brand: Samsung Pages: 190

Brand: Samsung Pages: 34

Brand: Samsung Pages: 2

Brand: Samsung Pages: 186

SGH E250 - Cell Phone 13 MB

Brand: Samsung Pages: 12

Brand: Samsung Pages: 185

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands