Aastra 9143i Series Administrator'S Manual Download | Manualshive

Page: 650 / 1140

background image

Operational Features

5-344

41-001160-04 Rev 02, Release 2.5

IP Phone Administrator Guide

Action URI Disconnected

The phones have a parameter, “

action uri disconnected

” that allow a disconnect

event to occur when the phone transitions from any active state (outgoing,
incoming, connected, or calling) to an idle state. This parameter can use the
variable “

$$LINESTATE$$

”.

If the Administrator enables this feature (by specifying a disconnect URI),
when a call is disconnected, the phone

checks to see if the event has a

Disconnect URI configured. If the phones finds a configured URI with a
$$LINESTATE$$ variable, it replaces the $$LINESTATE$$ variable with the
appropriate line state of the current active line. After all of the variables are
bound, the phone executes a GET on the URI. The following table lists the
applicable values for the $$LINESTATE$$ variable.

The Action URI Disconnect feature allows an Administrator to determine the
reason for the disconnect if required.

Note:

The

$$LINESTATE$$

variable is optional and not required when

enabling the “

action uri disconnected

” parameter.

$$LINESTATE$$ Value

Description

Meaning in a Disconnected URI

IDLE

Phone is idle.

N/A

DIALING

Phone is offhook and ready to dial.

N/A

CALLING

A SIP INVITE was sent but no response
was received.

Error occurred during the call.

OUTGOING

Remote party is ringing.

Call was cancelled.

INCOMING

Local phone is ringing.

Call was missed or cancelled.

CONNECTED

Parties are talking.

Call was successful.

CLEARING

Call was released but not acknowledged.

N/A

Note:

If you enable the Action URI Disconnect feature by specifying a

URI, the URI is called when any disconnect event occurs including an
intercom call or a conference setup.

«
...
648
649
650
651
652
...
»

Summary of Contents for 9143i Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 9143i Series

Univerge SV8100

Brand: NEC Pages: 4

Brand: Samsung Pages: 38

Brand: Samsung Pages: 114

Brand: Samsung Pages: 8

SCH-a610 Series

Brand: Samsung Pages: 12

Brand: Samsung Pages: 28

Brand: Samsung Pages: 28

Brand: Samsung Pages: 35

Brand: i.safe MOBILE Pages: 21

Brand: Unitech Pages: 81

Brand: Yealink Pages: 361

Brand: Yealink Pages: 7

Brand: Yealink Pages: 4

Brand: Yealink Pages: 2

Brand: Yealink Pages: 7

Brand: myPhone Pages: 41

Brand: Yealink Pages: 8

Brand: Pantech Pages: 261

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands