ABACUS Pisces Information Packet Download | Manualshive

Page: 12 / 17

background image

Abacus Pisces 069/Info.P 04/14v1a

12

www.abacushealthcare.com

0808 256 4249

Pisces

1700 Installation Requirements

Items

Items supplied with the kit should be as follows:
Bath Shell x 1 with 4 x inbuilt seal housings for the platform rods
Bathing/Changing Platform
Bath Surround Panels x 1
End Base units. Left x 1. Right x 1.
Bath Frame with platform support rods
Information pack
Flexible water feed pipes x2
Bath Shower Mixer Tap  (TMV) x1
Base unit Fixing kit (Comprising Bolts /screws – see Floor fixing kit on page 12)

Installation

Preparation of Site

a) Carefully remove all packaging and inspect the bath thoroughly. Note: Do not use sharp knives or
instruments to remove packaging around the finished surface areas of the bath.

b) Ensure all component parts are present before proceeding to remove any existing facilities. It is
important to ensure the complete kit is there. If there are ANY components missing contact the office and
quote the number on the side of the bath.

c) Prepare the floor area and ensure it is flat, level and structurally sound & there are

NO SERVICES BURIED

within the floor fixing area.

Bath Fitting

Ensure that the Site is ready as per the Pre Installation Requirements detailed in this pack.

REMOVE TRANSPORT CASTORS IF STILL IN PLACE. REMOVE TRANSPORT STRAPS - SEE PAGE 3.

Base Plate Fixing – THIS SECTION IS CRITICAL
See the Floor Fixing kit for the correct floor fixings to be used

Using the foot fixing template on the pre-install detail on page 4, mark out the floor fixing holes for the End
Base unit Feet. This template information is repeated (

FIG 1)

Starting with the bath tap end base plate, drill 2 holes for the appropriate fittings (Using the 400mm or
484mm centres) in the floor ensuring they are into a

solid construction

.

Clean out the holes & using the correct floor installation kit tighten up fully making sure the frame is vertical
in both planes. Repeat with the foot end base plate. Use the other holes to ensure extra fixing is made
but these are only additional and not critical.
It is important that both end plates are completely vertical (

FIG2

)

«
...
10
11
12
13
14
...
»

Summary of Contents for Pisces


















Reviews:

No comments

Related manuals for Pisces

Palermo Petite US-N4CCS

Brand: Crosswater Pages: 2

Brand: DURAVIT Pages: 7

Brand: Jacuzzi Pages: 12

Brand: Aquatic Pages: 8

Brand: Kohler Pages: 64

Brand: Kinedo Pages: 9

Brand: Kinedo Pages: 12

Sensation W30A-170-075W-A

Brand: AM.PM Pages: 16

Renaissance 047438-0070A

Brand: American Standard Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands