background image

Abacus Pisces 069/Info.P 04/14v1a 

 

 

INSTALLER INSTRUCTIONS 

 

 
This product is heavy. Two persons minimum to move the unit. 
 
Always check around the bath for any obstructions before raising or lowering the bath. 
Never drop or insert any objects into any openings. 
 

WARNING! 

Risk of electric shock; connect only to a separate circuit protected by an RCCB 

Risk of electric shock; do not permit electric appliances (such as a hair dryer, lamp, telephone, radio or 
television) within 2m of this bath. 
 
The unit must be connected to an RCCB. Such a circuit is to be provided by a qualified electrician and should 
be tested on a routine basis.  
To test the RCCB push the test button; the RCCB should interrupt power. Push the RESET button; power 
should be restored. If the RCCB fails to operate in this manner there is the possibility of an electrical shock. 

Do not use this unit

. Isolate the unit and have the problem corrected by a qualified service representative 

before any further use.  
Whirlpool and spa motors where fitted must be connected to an RCCB protected outlet as must any 
electrical accessories. 
 
Although compliant with IEC/EN60601-1-2 for EMC, the bath may still cause interference with sensitive 
medical equipment.  Should any electro-magnetic interference be experienced whilst using this product, 
remove the user immediately and seek medical advice. 
 
Where a safety lap belt is supplied this must be used for the safety of the bather. 

 
WARNING! 

 If this unit is to be utilised by many different bathers, we would strongly recommend that it is 

cleaned regularly with a medical disinfectant as well as following a strict cleaning routine. 
 

WARNING!

 

 This Bath moves. Ensure there are no objects or persons that can become trapped or injured 

while the bath raises or lowers. 
 

 
 
 
 
 

 

 

 

 

 

 

Transport wheels and Straps. 
Remove before installation. 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Pisces


















Reviews: