background image

Operating Instructions 

   

Temperaturregler 

 

Installation and electrical 

connection

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating Instructions | 1473-1-8290 

— 8 — 

   

Pos: 28 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/M  - O/M ontage und el ektrischer Anschl uss @ 23\mod_1336477157864_15.docx @ 209033 @ 1 @ 1 

 

Installation and electrical connection 

 

Pos: 29 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für  alle Dokumente <--)/Warnhinweise/Sicherheit - Ni ederspannungs- und 230  V-Leitungen @ 23\mod_1336558868201_15.docx @ 209164 @  @ 1 

 

 

 

Warning 

Electric voltage! 

Risk of death due to electrical voltage of 230 V during short-circuit in the low-voltage line. 
–  Low-voltage and 230 V lines must not be installed together in a flush-mounted socket! 

 
 

Pos: 30 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für  alle Dokumente <--)/Warnhinweise/Sicherheit - F achkenntnisse @ 23\mod_1336559183027_15.docx @ 209179 @ 2 @ 1 

 

7.1 

Requirements for the electrician 

 

 

 

Warning 

Electric voltage! 

Install the device only if you have the necessary electrical engineering knowledge and experience. 

  Incorrect installation endangers your life and that of the user of the electrical system. 

  Incorrect installation can cause serious damage to property, e.g. due to fire. 

 
The minimum necessary expert knowledge and requirements for the installation are as follows: 

  Apply the "five safety rules" (DIN VDE 0105, EN 50110):  

 

1.  Disconnect from power;  

 

2.  Secure against being re-connected;  

 

3.  Ensure there is no voltage; 

 

4.  Connect to earth and short-circuit; 

 

5.  Cover or barricade adjacent live parts. 

  Use suitable personal protective clothing. 

  Use only suitable tools and measuring devices. 

  Check the supply network type (TN system, IT system, TT system) to secure the following 

power supply conditions (classic connection to ground, protective earthing, necessary 
additional measures, etc.). 

 
 

Pos: 31 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/M  - O/M ontage @ 18\mod_1302615960458_15.docx @ 103424 @  2  @  1 

 

7.2 

Mounting 

 

Pos: 32 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für  alle Dokumente <--)/Warnhinweise/Sicherheit - 230 V @ 18\mod_1302606816750_15.docx @ 103308 @  @ 1 

 

 

 

Warning 

Electric voltage! 

Risk of death and fire due to electrical voltage of 230 V. 
–  Work on the 230V supply system may only be performed by authorised electricians!  
–  Disconnect the mains power supply prior to installation and/or disassembly! 

 
 

Pos: 33 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für  alle Dokumente <--)/++++++++++++ Seitenu+++++++++++ @ 9\mod_1268898668093_0.docx  @  52149 @   @ 1 

 

 

 

Summary of Contents for 1795 500 Series













Reviews: