background image

Operation Manual / 1 Introduction

1  Introduction / 1.1  Purpose of the manual

© Copyright 2017 ABB. All rights reserved.

HZTL4005_EN

Revision F

May 2017

1

Introduction

1.1

Purpose of the manual

Fig. 1: Serial number (01) on the rating plate

This Operation Manual belongs to the turbocharger with the identical serial number (01), see
chapter 3 (Safety data sheet) and the rating plate on the turbocharger.

Operation Manual

The Operation Manual explains the turbocharger and contains instructions for safe opera-
tion.

The Operation Manual is a complement to and expansion of existing national regulations for
occupational safety, accident prevention and environmental protection.

Target group

The Operation Manual is aimed at engineers and trained mechanics responsible for the
proper operation of the engine and for the turbocharger connected to it.

Availability of the Operation Manual

The Operation Manual must be available where the turbocharger is used.

All persons operating or working on the turbocharger must have read and fully understood
the Operation Manual.

Page 

2

 / 

7

Summary of Contents for A145-H66















































































































































Reviews: