background image

Operation Manual / 4 Product description / A130-M.. - A145-M..

3  Commissioning / 3.2  Inspection procedures

© Copyright 2017 ABB. All rights reserved.

HZTL4031_EN

Revision F

August 2017

3.2

Inspection procedures

3.2.1

Introduction

Inspection procedures include preventative visual controls, monitoring and measuring work
before and during commissioning. Inspection procedures enable changes to the turbochar-
ger to be detected. Engine damage can be prevented.

3.2.2

Checks before commissioning

Filter mat (if available)

u

Check for damage and contamination.

Lubricating system

 CAUTION

Contaminated oil

Serious damage to engine or property can be caused by dirt and solid ma-
terial particles in the oil.

u

For the initial commissioning phase and after all service work, flush the
complete lubricating system with warm oil.

u

Use special running-in filters when running in the engine and after all ser-
vice work on the lubricating system.

u

Check that the oil filter is clean before commissioning.

u

Check the oil pressure in the oil supply pipes.

Warning plates

u

Check whether warning plates are present and legible.

u

Check whether the protective sheets have been removed.

Version with compressor wheel cooling:

 CAUTION

Failure of compressor wheel cooling

Any prolonged failure of the compressor wheel cooling will shorten the re-
placement interval of the compressor wheel.

u

Make sure there is an uninterrupted supply of cooling air during opera-
tion.

u

Check whether the compressor wheel cooling is fitted on the bearing casing.

Page 

22

 / 

111

Summary of Contents for A145-H66















































































































































Reviews: