■
Altitude derating
At altitudes 1000 … 2000 m (3281 … 6562 ft) above sea level, the output current derating
is 1 percentage point for every added 100 m (328 ft). For example, the derating factor for
1500 m (4921 ft) is 0.95. For altitudes above 2000 m (6562 ft), contact ABB.
If surrounding air temperature is below +40 °C, the derating can be reduced by 1.5
percentage points for every 1 °C reduction in temperature. A few altitude derating curves
are shown below.
1500 m
1000 m
+25 °C
+30 °C
+77 °F
+86 °F
+40 °C
+104 °F
+35 °C
+95 °F
+20 °C
+68 °F
3300 ft
4921 ft
2000 m
6562 ft
2500 m
8202 ft
3000 m
9842 ft
3500 m
11429 ft
4000 m
13123 ft
1.00
0.95
0.85
0.90
0.80
Derating factor 1.00
Derating factor 0.95
Derating factor 0.90
Derating factor 0.85
Derating factor 0.80
For a more accurate derating, use the DriveSize PC tool.
■
Switching frequency derating
Switching frequencies other than 1.5 kHz can require output current derating. If you change
the minimum switching frequency with parameter
97.02 Minimum switching frequency
,
calculate the derated output current by multiplying the current given in the rating table by
the derating factor given in the table below. Changing parameter
97.01 Switching frequency
reference
does not require derating.
Derating factor (k) for the minimum switching frequencies
8 kHz
4 kHz
2 kHz
1 kHz
0.58
0.78
0.92
1
Technical data 139
Summary of Contents for ACH580-04
