Protecting the drive and input power cable in short-circuits
Protect the drive (1) with fuses (a) and the input cable with fuses (b) or a circuit breaker.
~
~
M
3~
b
a
1
Size the fuses or the circuit breaker according to local regulations for the input cable
protection. Select the fuses for the drive according to the instructions given in the technical
data. The fuses for the drive protection will restrict drive damage and prevent damage to
adjoining equipment in case of a short-circuit inside the drive.
Note:
If the fuses for the drive protection are placed at the distribution board and the input
cable is dimensioned according to the nominal input current of the drive given in the technical
data, the fuses protect also the input cable in short-circuit situations, restrict drive damage
and prevent damage to adjoining equipment in case of a short-circuit inside the drive. No
separate fuses for the input cable protection are needed.
■
Circuit breakers
The protective characteristics of circuit breakers depend on the type, construction and
settings of the breakers. There are also limitations pertaining to the short-circuit capacity of
the supply network. Your local ABB representative can help you in selecting the breaker
type when the supply network characteristics are known.
WARNING!
Due to the inherent operating principle and construction of circuit
breakers, independent of the manufacturer, hot ionized gases can escape from
the breaker enclosure in case of a short-circuit. To ensure safe use, pay special
attention to the installation and placement of the breakers. Obey the manufacturer’s
instructions.
Note:
Circuit breakers must not be used without fuses in UL installations.
Tested circuit breakers
You can use the circuit breakers listed in the technical data. Other circuit breakers can be
used with the drive if they provide the same electrical characteristics. ABB does not assume
any liability whatsoever for the correct function and protection with circuit breakers not listed.
Furthermore, if the recommendations given by ABB are not obeyed, the drive can experience
problems that the warranty does not cover.
Protecting the drive against ground faults
The drive is equipped with an internal ground fault protective function to protect the unit
against ground faults in the motor and motor cable. This function is not a personnel safety
or a fire protection feature. See the firmware manual for more information.
■
Residual current device compatibility
The drive is suitable to be used with residual current devices of Type B.
80 Guidelines for planning the electrical installation
Summary of Contents for ACH580-04
