ABB ACL30 User Manual Download | Manualshive

Page: 155 / 360

background image

Program features 155

Protection functions

The following functions can be used to check and ensure proper operation of elevator
control in different operating conditions: Speed match, Inverter overload, Motor stall
and Leveling overtime stop.

Other protection functions cover Thermal motor protection, DC voltage control and
Programmable protection functions.



Speed match

The Speed match function checks that the motor actual speed (speed estimate or
measured with an encoder, see parameter

SPEED FB SEL) follows the speed

reference within the desired window during acceleration, deceleration and when
running in a steady state (at set-point speed). The function also ensures that the
brake does not slip while the drive is in a stopped state with the brake closed.

You can enable the Speed match function with parameter

SPEED MATCH.

There are two parameters for defining the speed match deviation:

SPD STD

DEV LVL is used for checking the deviation in a steady state, whereas

SPD

RMP DEV LVL is used for checking the deviation during acceleration and
deceleration.

While the drive is running, it trips on fault SPEED MATCH if the following conditions
are met.

• The motor is running in a steady state and the difference of the motor actual

speed and the ramped speed reference is greater than the value of parameter

SPD STD DEV LVL for a period longer than defined with parameter

SPEED MATCH DLY.

Example: If parameter

SPD STD DEV LVL is set to 0.5 m/s, the drive will

not trip on fault SPEED MATCH as long the difference of the motor actual speed
and the speed reference does not exceed 0.5 m/s (that is, it does not go outside
the enclosed area in the figure below) for a period longer than defined with
parameter

SPEED MATCH DLY (0.5 s).

• The motor is accelerating/decelerating and the difference of the motor actual

speed and the ramped speed reference is greater than the value of parameter

SPD RMP DEV LVL for a period longer than defined with parameter

SPEED MATCH DLY.

Example: If parameter

SPD RMP DEV LVL is set to 0.6 m/s, the drive will

not trip on fault SPEED MATCH during acceleration/deceleration as long as the
difference of the motor actual speed and the ramped speed reference does not
exceed 0.6 m/s (that is, it does not go outside the enclosed area in the figure
below) for a period longer than defined with parameter

SPEED MATCH

DLY (0.5 s).

«
...
153
154
155
156
157
...
»

Summary of Contents for ACL30









































































































































































































































































































































































Reviews:

No comments

Related manuals for ACL30

Brand: YASKAWA Pages: 81

PowerXL DM1 Series

Brand: Eaton Pages: 258

Brand: YASKAWA Pages: 18

Brand: YASKAWA Pages: 139

8400 protec StateLine mit SO10

Brand: Lenze Pages: 66

Brand: SilverStone Pages: 2

Brand: D+H Pages: 20

Brand: FujiFilm Pages: 252

Brand: ABB Pages: 13

Brand: EKSMA OPTICS Pages: 12

Brand: IBM Pages: 20

Brand: Sealey Pages: 6

Brand: Becker Pages: 20

Brand: Lenze Pages: 43

Brand: Robotis Pages: 21

Brand: degdrive Pages: 251

Brand: Vicon Pages: 21

SteelDrive Focuser

Brand: Baader Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands