ABB ACL30 User Manual Download | Manualshive

Page: 168 / 360

background image

168 Program features



Autophasing modes

Several autophasing modes can be set with parameter

IDRUN MODE:

• For Turning mode without the load connected – select Autophs turn
• For Turning mode with the load connected – select Autophs rope
• For Static modes 1 and 2 perform pulse test with a closed brake – select

Autophs st1/ Autophs st2.

Turning mode

– is the most robust and accurate method. In this mode, the motor

shaft can be turned back and forward (±360/polepairs)° to determine the rotor
position. The ropes must be removed from the traction sheave for load free
movement.

Turning mode with ropes on

– can be used if the lift cabin is allowed to move few

tens of centimeters up. This method uses the natural unbalance of the lift when the
cabin is empty. During the autophasing procedure, the cabin moves few tens of
centimeters upward and during this movement drive detects the angle offset. The
cabins moves very slowly due to the drive braking feature.

Static modes

– can be used if the motor cannot be turned when the load is

connected. As the characteristics of different motors differ, test and select the suitable
mode.

Encoder angle offset write to 0

– The autophasing offset angle can be used to set

the zero position of encoder. When the autophasing offset angle is measured, it can
be written to the encoder memory as zero position with parameter

OFFSET SRC = Set zero pos. Also select parameter

ENC PAR REFRESH to

trigger the written value to encoder. After this configuration, the drive can use a zero
offset angle.

Settings

Parameters

Additional information

ENC PAR REFRESH

Forces a reconfiguration of the FEN-xx interfaces, which is needed for
any parameter changes in groups 90…93 to take effect.

USE GIVEN PARAMS

Activates the motor model parameters

and the rotor angle

offset parameter

POS OFFSET USER

Defines an angle offset between the zero position of the synchronous
motor and the zero position of the position sensor.

IDRUN MODE

Selects the type of the motor identification performed at the next start of
the drive in the DTC mode to identify the motor characteristics for
optimum motor control.

POS OFFSET SRC

Select the source for the angle offset between the zero position of the
synchronous motor and the zero position of the position sensor.

«
...
166
167
168
169
170
...
»

Summary of Contents for ACL30









































































































































































































































































































































































Reviews:

No comments

Related manuals for ACL30

Brand: D+H Pages: 16

Brand: Omron Pages: 8

Brand: CHINSC ELECTRIC Pages: 209

Brand: Simu Pages: 2

HF DRIVER - REPAIR

Brand: Altec Lansing Pages: 5

Brand: Parker Pages: 100

Brand: agrifac Pages: 26

Brand: KB Electronics Pages: 18

EUP200AD-1H12V-0

Brand: EUCHIPS Pages: 4

ZAdyn4CA 018 HY

Brand: ZIEHL-ABEGG Pages: 28

Brand: Binks Pages: 8

IM.60 24V + CPS

Brand: Fancom Pages: 55

Brand: WAREMA Pages: 14

Brand: Danfoss Pages: 142

Brand: Parker Pages: 545

DA1-32030-20 Series

Brand: Eaton Pages: 14

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 2

Brand: VAR Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands