US 2)
IEC 1)
Frame size
ACQ580-
07…
Cu cable type
Al cable type
Cu cable type
AWG/kcmil per
phase
mm2
mm2
3×600 MCM or 4×400
MCM
4×(3×240)
3×(3×240)
R11
0880A-4
U
n = 480 V
3/0
3×120
3×95
R6
0124A-4
250 MCM
3×150
3×120
R7
0156A-4
300 MCM
3×240
3×150
R7
0180A-4
2×2/0
2×(3×95)
2×(3×70)
R8
0240A-4
2×3/0
2×(3×120)
2×(3×95)
R8
0260A-4
2×250 MCM
2×(3×185)
2×(3×120)
R9
0361A-4
2×300 MCM
2×(3×240)
2×(3×150)
R9
0414A-4
2×500/3×250 MCM
3x(3x150)
3x(3x95)
R10
0505A-4
3×300 MCM
4x(3x150)
3x(3x120)
R10
0585A-4
3×300 MCM
4x(3x150)
3x(3x150)
R10
0650A-4
3x500/4x300 MCM
4x(3x185)
3x(3x185)
R11
0725A-4
3×600/4x400 MCM
4x(3x240)
3x(3x240)
R11
0820A-4
3x600/4x400 MCM
4x(3x240)
3x(3x240)
R11
0880A-4
1. The cable sizing is based on max. 9 cables laid on a cable ladder side by side, three ladder
type trays one on top of the other, ambient temperature 30 °C, PVC insulation, surface
temperature 70 °C (EN 60204-1and IEC 60364-5-52/2001). For other conditions, size the
cables according to local safety regulations, appropriate input voltage and the load current of
the drive.
2. The cable sizing is based on NEC Table 310-16 for copper wires, 75 °C (167 °F) wire insulation
at 40 °C (104 °F) ambient temperature.Not more than three current-carrying conductors in
raceway or cable or earth (directly buried). For other conditions, size the cables according to
local safety regulations, appropriate input voltage and the load current of the drive.
Losses, cooling data and noise
Noise
Heat dissipa-
tion
Air flow
ACQ580-
07…
IP54 (UL Type 12)
IP21, IP42 (UL Type 1)
dB(A)
W
cfm
m3/h
cfm
m3/h
U
n = 480 V
67
2487
344
585
403
685
0145A-4
67
2497
353
600
412
700
0169A-4
67
3314
353
600
412
700
0206A-4
65
3806
412
700
470
800
0246A-4
65
4942
412
700
470
800
0293A-4
208 Technical data
Summary of Contents for ACQ580-07
