background image

ABB VARIABLE FREQUENCY DRIVES

RENEWAIRE.COM  

ABB VFD SUPPLEMENTAL MANUAL  

1.800.627.4499

14

SETTINGS

OPERATION

SCALING AND RESPONSE TO ANALOG INPUTS

The most likely reason to control the VFD from 
an analog signal is to automatically change the 
amount of outside air ventilation to meet the actual 
needs for each time period.

If one or both of the VFDs will be controlled by an 
analog input from an external Control Device (e.g. a 
CO2 controller or a Building Management System), 
you may need to “scale” the rate of response of the 
VFD(s) to the rate of change of the analog signal.

We need to introduce two concepts relating to the 
amount of outside air ventilation needed in the building:

•  The “ACTION LEVEL” is the level of measurement 

of indoor air quality or occupancy at which 
the ERV should start to deliver more than the 
“Design Minimum Supply Airfl ow”;

•  The “MAXIMUM RESPONSE LEVEL” is the level of 

measurement of indoor air quality or occupancy 
at which the ERV should be operating at the 
“Design Maximum Supply Airfl ow”.

Do not change PARAMETER 2003 MAX CURRENT from RenewAire default setting, which should be set 
to no more than 125% of the motor nameplate FLA for motors with 1.15 Service Factor (SF) or higher 
or 115% of the motor FLA for motors with less than 1.15 SF and otherwise unprotected. This parameter 
controls the Motor OVERLOAD PROTECTION provided by the VFD.

DANGER OF MOTOR OVERLOAD LEADING TO SMOKE AND FIRE!

WARNING

 

F9

SCHEMATIC RELATIONSHIP EXAMPLE BETWEEN MEASUREMENT BY A CONTROLLER, THE ANALOG 

SIGNAL FROM THE CONTROLLER, THE VFD SCALING PARAMETERS AND THE MOTOR SPEED 

(VFD OPERATING FREQUENCIES).

0

2000

4mA

20mA

0vdc

10vdc

ACTION LEVEL

MAXIMUM RESPONSE LEVEL

1104 "REF1 MIN"

MEASURED CONDITION

ANALOG SIGNAL FROM

CONTROLLER

0hz

60hz

10hz

20hz

30hz

40hz

50hz

500

1000

1500

1105 "REF1 MAX"

LEVEL AT MAXIMUM DEVICE OUTPUT

(CO

2

 CONCENTRATION IN THIS EXAMPLE)

1301 MINIMUM AI1

in this example = 55%"

1302 MAXIMUM AI1

in this example = 91%"

0

Summary of Contents for ACS320 series

















Reviews: