ABB ACS860 Firmware Manual Download | Manualshive

Page: 66 / 438

background image

66 Program features

The motor temperature can be monitored using

• the motor thermal protection model (estimated temperature derived internally

inside the drive), or

• sensors installed in the windings. This will result in a more accurate motor model.

Motor thermal protection model

The drive calculates the temperature of the motor on the basis of the following
assumptions:

1. When power is applied to the drive for the first time, the motor is assumed to be at

ambient temperature (defined by parameter

Motor ambient temperature

After this, when power is applied to the drive, the motor is assumed to be at the
estimated temperature.

2. Motor temperature is calculated using the user-adjustable motor thermal time and

motor load curve. The load curve should be adjusted in case the ambient
temperature exceeds 30 °C.

The motor thermal protection model fulfills standard IEC/EN 61800-5-1 ed. 2.1
requirements for thermal memory retention and speed sensitivity. The estimated
temperature is retained over power down. Speed dependency is set by parameters

Motor load curve

,

Zero speed load

and

.

Note:

The motor thermal model can be used when only one motor is connected to

the drive.

Temperature monitoring using PTC sensors

One PTC sensor can be connected to digital input DI6.

The resistance of the PTC sensor increases when its temperature rises. The
increasing resistance of the sensor decreases the voltage at the input, and eventually
its state switches from 1 to 0, indicating overtemperature.

1…3 PTC sensors can also be connected in series to an analog input and an analog
output. The analog output feeds a constant excitation current of 1.6 mA through the
sensor. The sensor resistance increases as the motor temperature rises, as does the
voltage over the sensor. The temperature measurement function calculates the
resistance of the sensor and generates an indication if overtemperature is detected.

For wiring of the sensor, refer to the

Hardware Manual

of the drive.

DI6

+24VD

T

«
...
64
65
66
67
68
...
»

Summary of Contents for ACS860























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACS860

Brand: D+H Pages: 12

Brand: Kieback&Peter Pages: 10

Brand: Leadshine Pages: 15

Brand: Iomega Pages: 16

Brand: Metronix Pages: 171

Brand: YASKAWA Pages: 288

Brand: YASKAWA Pages: 513

EUP200AD-1H12V-0

Brand: EUCHIPS Pages: 4

Brand: SMC Corporation Pages: 419

Brand: HPI Racing Pages: 2

Brand: Pacific Digital Pages: 24

Brand: SMS Pages: 75

DataPort DP25 6G

Brand: CRU Pages: 4

Brand: LaCie Pages: 33

Brand: IBM Pages: 50

Brand: Danfoss Pages: 241

ZPSA-600-EH1-FR Series

Brand: YASKAWA Pages: 42

Brand: Wavelength Electronics Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands