188 Technical data
Category C4
cannot be met, the requirements of the standard can
be met as follows:
1. It is ensured that no excessive emission is propagated to neighbouring low-voltage
networks. In some cases, the natural suppression in transformers and cables is
sufficient. If in doubt, the supply transformer with static screening between the primary
and secondary windings can be used.
2. An EMC plan for preventing disturbances is drawn up for the installation. A template is
available from the local ABB representative.
3. The motor and control cables are selected as specified in the hardware manual.
4. The drive is installed according to the instructions given in the hardware manual.
WARNING!
A drive of category C4 is not intended to be used on a low-voltage public
network which supplies domestic premises. Radio frequency interference is expected if
the drive is used on such a network.
UL marking
UL checklist
•
The drive is to be used in a heated, indoor controlled environment. The drive must be
installed in clean air according to enclosure classification. Cooling air must be clean,
free from corrosive materials and electrically conductive dust. See page
.
•
The maximum ambient air temperature is 40 °C (104 °F) at rated current. The current
is derated for 40 to 50 °C (104 to 122 °F).
•
The drive is suitable for use in a circuit capable of delivering not more than 100,000
rms symmetrical amperes, 500 V maximum when the input cable is protected with
class T fuses given. The ampere rating is based on tests done according to UL 508A.
•
The cables located within the motor circuit must be rated for at least 75 °C in UL-
compliant installations.
•
The input cable must be protected with fuses. Circuit breakers must not be used
without fuses in the USA. For suitable circuit breakers, contact your local ABB
representative. Suitable IEC (class aR) fuses and UL fuses for drive protection are
listed starting on page
.
Low
voltage
Equipment
Low
voltage
Equipment
Equipment
(victim)
Supply transformer
Medium voltage network
Static screen
Point of measurement
Drive
Neighbouring
network
Summary of Contents for ACS880-17
