background image

If necessary, change the SIM card’s PIN code by using a mobile phone.

3.

If automatic APN discovery does not work, define the APN settings.
3.1. Set 

APN Type

 to 

Manual

.

3.2. Type the cellular access point name in the 

APN 

field according to the

network operator’s instructions.

By default, the device uses automatic APN discovery with default APN
values based on the network ID received from the cellular network. When

APN Type

 is set to “Manual”, the access point works as a gateway from the

cellular network to the Internet. There are public and private access points. A
public access point is usually defined. A private access point requires contract
with a cellular operator. The device is compatible with both public and
private access points.

4.

If the cellular network’s access point requires authentication, define the
authentication settings according to the network operator’s instructions.
4.1. Set 

Authentication

 to 

PAP

 or 

CHAP

.

4.2. Type the access point’s username in the 

Username

 field.

4.3. Type the access point’s password in the 

Password

 field.

5.

If the device acts as a wireless router to Ethernet devices, and DNS is needed,
enter the DNS settings.

Set 

DNS Selection

 to 

From Network

 to set up the device to receive

DNS server IP addresses automatically from the cellular network.

Set 

DNS Selection

 to 

Manual

 to set up the device to use DNS servers

manually defined in the 

DNS Servers

 field.

6.

Click 

Submit

 to save the settings.

7.

Restart the device to activate the configuration.

5.2.4 

Setting WAN failover and backup routing

1.

In the left pane, click 

Network WAN Failover

.

2.

Set 

WAN Default Route

 to 

Yes

.

This setting enables the use of the Ethernet WAN or the Mobile WAN as the
default route interface.

3.

Set the value of 

Mobile WAN On Demand

.

If the backup WAN interface needs to come up only when the primary
interface goes down, select 

Yes

.

If both the wireless and Ethernet WAN interfaces have to be up all the
time, select 

No

.

4.

Click 

Submit

 to save the settings.

5.

Restart the device.

Section 5

1MRS758456 H

Network configuration

26

ARG600 Single SIM Variant

User Manual

Summary of Contents for ARG600 Single SIM Variant

































































Reviews: