background image

7

1SDH000759R0002, L4106

Installation and operating instructions, ATS021

2. Product overview

2. Product overview

The transfer switch concept is applied to any installations requiring switching from the main power circuit 

to another to ensure the supply of loads.

2.1 Typical applications

A. Network line – GenSet line

In case of loss of the main’s network, the ATS021 device manages the switching to the emergency line 

equipped with a GenSet system.

Figure 2.2 

Network line a - Network line b

Automatic transfer switch type ATS021 is designed for single- and three-phase distribution systems in 

diverse applications. ATS021 will control the switching between two power supplies. The ATS021 unit 

measures the voltage level of the normal line and controls the two main protection devices of the two 

monitored lines in order to guarantee the continuity of the power supply.

Figure 2.1 

Network line - GenSet line

B. Network line a – Network line b

In case of loss of the main’s network, the ATS021 device manages the switching to a second line used 

as an emergency source. 

G

KA00427

KA00428

Summary of Contents for ATS021





































Reviews: