background image

Overview of this manual

About this manual

This manual describes the discrete I/O devices and contains instructions for the
configuration.

Usage

This manual should be used during installation and configuration of the discrete
I/O devices.

Who should read this manual?

This manual is intended for

Personnel responsible for installations and configurations of industrial network
hardware/software

Personnel responsible for I/O system configuration

System integrators

Prerequisites

The reader should have the required knowledge of

Mechanical installation work

Electrical installation work

System parameters and how to configure them

RobotStudio

References

Document references

Document ID

Reference

3HAC032104-001

Operating manual - RobotStudio

3HAC065036-001

Operating manual - OmniCore

3HAC060860-001

Product manual - OmniCore C30

3HAC065041-001

Technical reference manual - System parameters

3HAC065038-001

Technical reference manual - RAPID Instructions, Functions
and Data types

3HAC066554-001

Application manual - Controller software OmniCore

3HAC065034-001

Product specification - OmniCore C line

3HAC066565-001

Application manual - EtherNet/IP Scanner/Adapter

Other references

Description

Reference

ODVA Specification comprises two volumes from
the library:

Volume One: Common Industrial Pro-

tocol (CIP) Specification

and

Volume Two: Ether-

Net/IP Adaptation of CIP

.

EtherNet/IP

TM

Specification

, Edition 1.2

Continues on next page

Application manual - Discrete I/O

7

3HAC070208-001 Revision: C

© Copyright 20192020 ABB. All rights reserved.

Overview of this manual

Summary of Contents for Discrete I/O



























































Reviews: