ABB DressPack Product Manual Download | Manualshive

Page: 29 / 258

background image

1.2.4.6 Risks associated with live electric parts

Voltage related risks, general

Work on the electrical equipment of the robot must be performed by a qualified
electrician in accordance with electrical regulations.

•

Although troubleshooting may, on occasion, need to be carried out while the
power supply is turned on, the robot must be turned off (by setting the main
switch to OFF) when repairing faults, disconnecting electric leads and
disconnecting or connecting units.

•

The main supply to the robot must be connected in such a way that it can
be turned off from outside the working space of the robot.

•

Make sure that no one else can turn on the power to the controller and robot
while you are working with the system. A good method is to always lock the
main switch on the controller cabinet with a safety lock.

The necessary protection for the electrical equipment and robot system during
construction, commissioning, and maintenance is guaranteed if the valid regulations
are followed.

All work must be performed:

•

by qualified personnel

•

on machine/robot system in deadlock

•

in an isolated state, disconnected from power supply, and protected against
reconnection.

Voltage related risks, IRC5 controller

A danger of high voltage is associated with, for example, the following parts:

•

Be aware of stored electrical energy (DC link, Ultracapacitor bank unit) in
the controller.

•

Units such as I/O modules, can be supplied with power from an external
source.

•

The main supply/main switch

•

The transformers

•

The power unit

•

The control power supply (230 VAC)

•

The rectifier unit (262/400-480 VAC and 400/700 VDC. Note: capacitors!)

•

The drive unit (400/700 VDC)

•

The drive system power supply (230 VAC)

•

The service outlets (115/230 VAC)

•

The customer power supply (230 VAC)

•

The power supply unit for additional tools, or special power supply units for
the machining process.

•

The external voltage connected to the controller remains live even when the
robot is disconnected from the mains.

•

Additional connections.

Continues on next page

Product manual - DressPack/SpotPack IRB 8700

29

3HAC055802-001 Revision: B

© Copyright 2015-2017 ABB. All rights reserved.

1 Safety

1.2.4.6 Risks associated with live electric parts

«
...
27
28
29
30
31
...
»

Summary of Contents for DressPack



































































































































































































































































Reviews:

No comments

Related manuals for DressPack

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: Gary Machinery Pages: 14

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Tablet1000 Series

Brand: Hantek Pages: 98

Brand: Yamaha Pages: 31

REBOUND DUAL ST

Brand: Össur Pages: 104

Brand: Össur Pages: 130

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brand: Össur Pages: 8

Brand: Össur Pages: 72

Brand: Össur Pages: 76

Miami Lumbar Posteo

Brand: Össur Pages: 45

Brand: Össur Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands