background image

Type HCB-1 Pilot Wire Relay System

41-971.3M

7

(I

A2

 is the phase A negative sequence current):

But:

So:

Equ. (6)

For T = 4

I

S

 = 0.5

4.2.

NOMINAL PICKUP (All Relays)

The nominal pickup, I

nom

, is defined as

Equ. (7)

Where

I

nom

= total internal fault current

K

= number of relays (2 or 3)

I

S

= single-relay pickup with pilot

wire disconnected (see above)

0.2

T

.2

I

A

1

.46

I

A

2

4.9 

I

A

0

+

+

=

I

A

1

0.2

T

5.2

-----------

I

A

2

I

A

0

=

=

=

I

S

I

A

1

I

A

2

I

A

0

+

=

=

=  3

I

A

1

0.2

T

(

)

3

( )

I

S

3

I

A

1

0.2

T

3

×

(

)

5.2

-------------------------

0.12

T

  (A-G Fault)

=

=

=

I

nom

KI

S

=

For example, in the previous example or a phase-A-
ground fault, the single-relay pickup was determined
as I

S

 = 0.5 ampere for 4CH taps with the pilot-wire

open. For a two-terminal line, the nominal pickup for
a phase-A-to-ground fault (4CH taps) is:

4.3.

MINIMUM TRIP (All Relays)

With equal inputs to all relays and zero pilot-wire
shunt capacitance, the relays will operate at their
nominal pickup point. The minimum trip points will
vary somewhat from nominal value, depending on
the pilot-wire constants and the magnitude and
phase angle of the various relay input currents. For
example, Figure 6 shows the relay operating points
for a two-terminal line, assuming input current one
relay only.

An example of the characteristics with various cur-
rent distributions shown in Figure 6. The filter output
voltage, V

F

, of each relay, as defined by equation (1)

must be in phase or 180 degrees out-of-phase, in
order for Figure 7 to apply.

4.4.

INSULATING TRANSFORMER

Unless otherwise noted, all characteristics presented
include an insulating transformer with each relay.
Two ratios are available: 4/1 and 6/1. The high volt-
age side (H1-H4 Terminals) is connected to the pilot-
wires.

I

nom

A

 

to

 

G

(

)

0.5

0.5

2

×

1.0 

ampere

=

=

=

Sub 4

183A61

Figure 4. Simplified External Schematic of the HCB-1 Relay System

Summary of Contents for HCB-1





























Reviews: