background image

Operation Manual / A130-H.. - A140-H..

12 Material and Disposal / 12.2 Disposing of turbocharger components

© Copyright 2021 ABB. All rights reserved.

HZTL4030_EN

Rev.G

July 2021

12.2

Disposing of turbocharger components

 WARNING

Handling damaged thermal insulation

Damaged thermal insulation can lead to dust exposure. The glass fibres can
cause mechanical irritation of the eyes, skin, and respiratory tracts.

u

Avoid the formation of dust.

u

Vacuum up dust with a suitable vacuum cleaner.

u

Wear a respiratory mask to protect against dusts (P1 or P2 mask).

u

Wear safety gloves.

Wear safety goggles.

Wear a respiratory mask to protect against dusts.

Wear safety gloves to protect against mechanical hazards.

Disposal must be environmentally compatible, professional, and in compliance with locally
applicable regulations.

The turbocharger consists largely of metal (cast iron materials, steel, nickel-steel alloys, alu-
minium and bearing brass).

Further components are: Non-metallic materials (filter components of felt and polyethylene),
lubricants (engine oil), electronic parts (speed sensor and associated components), and
thermal insulation.

u

Dispose of metals as scrap metal for recycling.

u

Dispose of non-metallic materials as waste.

u

Dispose of residues of lubricants as waste oil.

u

Dispose of electronic components as electronic waste.

u

Dispose of thermal insulation as hazardous waste.

Page 

109

 / 

122

Summary of Contents for HT608279





























































































































Reviews: