ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download

Page: 14 / 488

ABB i-bus

KNX

Product Overview

14 2CDC508198D0211 Rev. A | AC/S 1.x.1

Product overview

3.1

Product overview

The devices are modular DIN rail component (MDRC) in the pro

design. The module width of the

devices is 4 space units. The devices are designed for installation in distribution boards on 35 mm
mounting rails.

The devices are powered by the bus and require an additional supply voltage, either 24 V AC/DC or Power
over Ethernet (PoE).

The device connects to the

ABB i-bus

KNX via the front bus connection terminal.

The software application Engineering Tool Software (ETS) is used for physical address assignment and for
setting the parameters.

The device is ready for operation after connecting the bus voltage and the supply voltage.

Abbreviation

Description

Application

Controller

MDRC

Application

KNX

KNX + BACnet

Version number (x = 1, 2 etc.)

Table 3: Product name description

3.2

Ordering details

Description

MB Type

Order No.

Packaging
unit [pcs.]

Weight
1 pc.
[g]

Application Controller, Basic

AC/S 1.1.1

2CDG110205R0011

192

Application Controller, BACnet

AC/S 1.2.1

2CDG110206R0011

192

Table 4: Ordering details

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands

ABB i-bus KNX AC/S 1.x.1 Series, Product Manual

Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands