ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download

Page: 162 / 488

ABB i-bus

KNX

Parameters

162 2CDC508198D0211 Rev. A | AC/S 1.x.1

•

And

: The input values are combined using a logical AND operator.

Value 1

Value 2

Value used

Main data point type

Data point type

Definition of the data point type that is transferred between the interfaces.

You will find further information on the data point types in

chapter 4.7 Data point types

The selection available may be restricted depending on the parameters above.

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands

ABB i-bus KNX AC/S 1.x.1 Series, Product Manual

Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands