ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download | Manualshive

Page: 248 / 488

background image

ABB i-bus

®

KNX

Parameters

248 2CDC508198D0211 Rev. A | AC/S 1.x.1

Radiator exponent

Options:

None/Linear (1.0)

Floor heating (1.05)

Floor heating (1.10)

Flat radiators (1.20)

Flat radiators (1.25)

Radiator to DIN 4703 (1.30)

Flat radiators (1.33)

Convectors (1.35)

Convectors (1.40)

Convectors (1.45)

Convectors (1.50)

The radiator exponent is dependent on the type and design of the heating element
and is normally stated by the manufacturer. The radiator exponent describes the
relationship between the increasing supply temperature and the non-proportionally
increasing heat dissipation into the room.

This information is used to calculate the heating curve. The higher this value is, the
more curved the heating curve is.

Start supply temperature curve at outside temperature

Options:

-100…19…100 °C

The outside temperature at which heating is started is specified using this parameter.
This value is the start of the heating curve. The heating limit is dependent on the
insulation standards in the building and can be selected lower, the better the building
is insulated.

«
...
246
247
248
249
250
...
»

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: NCR Pages: 6

Brand: Parker Pages: 30

Brand: VAT Pages: 22

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: Fairchild Pages: 2

Brand: Fagor Pages: 103

Brand: ZirbenLüfter Pages: 36

Brand: ZIMO Pages: 38

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Eaton Pages: 8

Brand: S&P Pages: 17

Brand: S&S Northern Pages: 9

Brand: UNISENSE Pages: 16

Brand: Xylem Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands