ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download | Manualshive

Page: 297 / 488

background image

ABB i-bus

®

KNX

Parameters

AC/S 1.x.1 | 2CDC508198D0211 Rev. A 297

Supply setpoint temperature

In this parameter window it is specified how the supply setpoint temperature for the heat generator is
calculated.

Supply temperature control

Options:

No (checkbox cleared)

Yes (checkbox selected)

On the selection of the

Yes

option, the ASM calculates the supply setpoint temperature and sends the

value calculated to the heat generator via the group object. Other parameters define how the calculation is
undertaken.

Selection of

Yes

option:

Dependent parameter(s):

Supply setpoint temperature source

Options:

ASM input socket

WebUI Input

BACnet input object

Calculated weather compensated

This parameter determines how the supply setpoint temperature is determined for the heat
generator. This setpoint is sent to the heat generator via the group object.

•

ASM input socket:

The supply setpoint temperature received via the input socket on the ASM is

used. This is an ASM multiple socket on which the highest value present is used.

•

WebUI Input:

The supply setpoint temperature is set on the web user interface for the ASM.

•

BACnet input object:

The supply setpoint temperature received via the BACnet object for the

ASM is used.

•

Calculated weather compensated:

The module calculates the supply setpoint temperature

currently required based on the outside temperature.

«
...
295
296
297
298
299
...
»

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

BT300 BurnerTronic

Brand: Lamtec Pages: 48

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: R82 Pages: 11

Brand: EasySMX Pages: 11

Brand: EasySMX Pages: 8

Brand: xpr Pages: 4

Brand: ABB Pages: 17

Brand: Daikin McQuay Pages: 8

Brand: IR-Tec Pages: 14

Brand: Hach Pages: 504

Brand: One for All Pages: 15

Brand: VAT Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands