ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download | Manualshive

Page: 401 / 488

background image

ABB i-bus

®

KNX

Parameters

AC/S 1.x.1 | 2CDC508198D0211 Rev. A 401

Supply temperature page

On this page it is shown how the supply setpoint temperature is calculated. The settings on which the
calculation is based can be changed.

The information displayed on this page may vary depending on which settings have been selected for the
supply setpoint temperature calculation in the ASM settings.

This section displays the current outside temperature that is used by the module for the calculation.

The parameter set in the ASM settings can be changed in this section via the web user interface. This is
advantageous so that the settings can be adapted to the local situation during the operating of the system
without renewed ETS programming.

The settings on the web user interface always apply. The parameters set in the ASM settings are
overwritten and only become active again on the reinstallation of the ASM.

The supply setpoint temperature output by the module is limited using the

Min. supply temperature

parameter. This is a safety function that ensures a supply setpoint temperature too low for the cooling
system is not output under any circumstances. For example, the supply setpoint temperature for cooling
ceiling can be limited to minimum 14 °C.

«
...
399
400
401
402
403
...
»

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i-bus KNX AC/S 1.x.1 Series

ServeRAID M5014

Brand: IBM Pages: 106

Brand: Galcon Pages: 32

Brand: ZIMO Pages: 38

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Daikin Pages: 38

Brand: Daikin Pages: 2

Brand: Daikin Pages: 148

Brand: Daikin Pages: 12

Brand: Daktronics Pages: 52

Brand: Waeco Pages: 20

Brand: Z-Wave Pages: 56

Brand: Dakota Digital Pages: 6

CMD-2000 Series

Brand: Dakota Digital Pages: 10

Brand: Z-Wave Pages: 6

Brand: Datalogic Pages: 15

Brand: RAKwireless Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands