ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download

Page: 466 / 488

ABB i-bus

KNX

Parameters

466 2CDC508198D0211 Rev. A | AC/S 1.x.1

7.20.3

Sockets

Overview of the ASM sockets for linking to other modules:

Type

Object name

Data type

Input

Trend1

Configuration-dependent

Input

Trend2

Configuration-dependent

Input

Trend3

Configuration-dependent

Input

Trend4

Configuration-dependent

Input

Trend5

Configuration-dependent

Input sockets

Object name

Data type

Trend1

Configuration-dependent

This input socket is always available.

Input for recorded value 1.

Signal value:

Configuration-dependent

Trend2

Configuration-dependent

The module has this input socket if the

option or greater is selected for the

Number of trends

parameter.

Input for recorded value 2.

Signal value:

Configuration-dependent

Trend3

Configuration-dependent

The module has this input socket if the

option or greater is selected for the

Number of trends

parameter.

Input for recorded value 3.

Signal value:

Configuration-dependent

Trend4

Configuration-dependent

The module has this input socket if the

option or greater is selected for the

Number of trends

parameter.

Input for recorded value 4.

Signal value:

Configuration-dependent

Trend5

Configuration-dependent

The module has this input socket if the

option is selected for the

Number of trends

parameter.

Input for recorded value 5.

Signal value:

Configuration-dependent

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands

ABB i-bus KNX AC/S 1.x.1 Series, Product Manual

Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands