ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download

Page: 98 / 488

ABB i-bus

KNX

Parameters

98 2CDC508198D0211 Rev. A | AC/S 1.x.1

Application example

This element can also be used as a send trigger.

In the example below, the result of the MIN/MAX element is always triggered for sending when the
"Update" input receives a telegram. The

Send trigger

parameter in 1-MUX must be activated.

Other

If an unlinked input is selected, the output value remains unchanged.

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands

ABB i-bus KNX AC/S 1.x.1 Series, Product Manual

Search results

Summary of Contents for i-bus KNX AC/S 1.x.1 Series

Reviews:

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brands by name

Popular brands