ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download | Manualshive

Page: 191 / 488

background image

ABB i-bus

®

KNX

Parameters

AC/S 1.x.1 | 2CDC508198D0211 Rev. A 191

Fan coil unit, fan speed

Options:

Display

set (slave) DPT 5.001

set (slave) 5.010

This parameter specifies whether the fan speed set by the room thermostat is only to be displayed
on the web user interface, or it can also be changed by the user. The current value is output on the
ASM output socket and in a BACnet object.

•

Display:

The fan speed is only displayed on the web user interface and cannot be changed.

•

set (slave) DPT 5.001:

The fan speed can be changed on the web user interface.

This setting functions only with ABB and Busch-Jaeger devices with the new master/slave
interface with group objects of type DPT 5.001

•

set (slave) DPT 5.010:

The fan speed can be changed on the web user interface.

This setting functions only with ABB and Busch-Jaeger devices with the old master/slave
interface with group objects of type DPT 5.010.

Selection of

Display

or

set (slave) DPT 5.001

option:

Dependent parameter(s):

Fan coil unit, type of fan

Options:

On/Off

3 stages

5 stages

Continuous fan 0...100%

Setting for the fan type. This setting must match the settings in the room thermostat.

•

On/Off:

Not a multiple stage fan type. The fan can only be switched on and off

•

3 stages:

Fan with 3 stages (0,1,2,3)

•

5 stages:

Fan with 5 stages (0,1,2,3,4,5)

•

Continuous fan 0...100%:

Continuous fan

«
...
189
190
191
192
193
...
»

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brand: Samsung Pages: 27

Brand: Lattice Semiconductor Pages: 26

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: Datavideo Pages: 8

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brand: jablotron Pages: 2

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: Danfoss Pages: 2

Brand: Desoutter Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands