ABB i-bus KNX AC/S 1.x.1 Series Product Manual Download | Manualshive

Page: 477 / 488

background image

ABB i-bus

®

KNX

Maintenance and cleaning

AC/S 1.x.1 | 2CDC508198D0211 Rev. A 477

10

Maintenance and cleaning

10.1

Maintenance

The device is maintenance-free. In the event of damage, e.g. during transport and/or storage, repairs are
not allowed to be made.

10.2

Cleaning

Disconnect the device from the supply of electrical power before cleaning. If devices become dirty, they
can be cleaned using a dry cloth or a cloth dampened with a soapy solution. Corrosive agents or solutions
must never be used.

«
...
475
476
477
478
479
...
»

Summary of Contents for i-bus KNX AC/S 1.x.1 Series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i-bus KNX AC/S 1.x.1 Series

Brand: GE Pages: 425

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: PAC Pages: 17

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: K1EL Pages: 46

Brand: Pando Pages: 43

Brand: Xilinx Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands