KNX Technical Reference Manual
ABB-i-Bus
®
-KNX Millenium
KNX Technical Reference Manual | 1473-1-8681
— 4 —
11.3.56
Additional cooling stage - Control value difference for sending of cooling control value ....................... 51
11.3.57
Additional cooling stage - Cyclic sending of the control value (min) ...................................................... 51
11.3.58
Additional cooling stage - Maximum control value (0 - 255) .................................................................. 51
11.3.59
Additional cooling stage - Minimum control value for basic load (0 - 255)............................................. 52
11.3.60
Settings of basic load ............................................................................................................................ 52
11.3.61
Settings of basic load - Minimum control value for basic load > 0 ......................................................... 52
11.3.62
Combined heating and cooling modes .................................................................................................. 52
11.3.63
Combined heating and cooling modes - Switchover of heating/cooling ................................................ 53
11.3.64
Combined heating and cooling modes - Operating mode after reset .................................................... 53
11.3.65
Combined heating and cooling modes - Heating/cooling control value output ...................................... 53
11.3.66
Combined heating and cooling modes - Additional heating/cooling stage control value output ............ 54
11.3.67
Setpoint settings ................................................................................................................................... 54
11.3.68
Setpoint settings - Setpoint for heating comfort = setpoint for cooling comfort ..................................... 54
11.3.69
Setpoint settings - Hysteresis for switchover heating/cooling (x 0.1°C) ................................................ 55
11.3.70
Setpoint settings - Setpoint temperature for heating and cooling comfort (°C) ...................................... 55
11.3.71
Setpoint settings - Setpoint temperature for heating comfort (°C) ......................................................... 55
11.3.72
Setpoint settings - Reduction for standby heating (°C) ......................................................................... 55
11.3.73
Setpoint settings - Reduction for ECO heating (°C) .............................................................................. 56
11.3.74
Setpoint settings - Set-point temperature for frost protection (°C) ......................................................... 56
11.3.75
Setpoint settings - Setpoint temperature for cooling comfort (°C) ......................................................... 56
11.3.76
Setpoint settings - Increase for standby cooling (°C) ............................................................................ 56
11.3.77
Setpoint settings - Increase for ECO cooling (°C) ................................................................................. 57
11.3.78
Setpoint settings - Set-point temperature for heat protection (°C) ......................................................... 57
11.3.79
Setpoint settings - Display indicates ..................................................................................................... 57
11.3.80
Setpoint settings - Display indicates ..................................................................................................... 57
11.3.81
Setpoint settings - Send current setpoint .............................................................................................. 58
11.3.82
Setpoint settings - Cyclic sending of the current set-point temperature (min) ....................................... 58
11.3.83
Setpoint adjustment .............................................................................................................................. 58
11.3.84
Setpoint adjustment — Maximum manual increase during heating mode (0 - 15°C) ............................ 58
11.3.85
Setpoint adjustment — Maximum manual reduction during heating mode (0 - 15°C) ........................... 58
11.3.86
Setpoint adjustment — Maximum manual increase during cooling mode (0 - 15°C) ............................ 59
11.3.87
Setpoint adjustment — Maximum manual reduction during cooling mode (0 - 15°C) ........................... 59
11.3.88
Setpoint adjustment - Resetting of the manual adjustment for receipt of a basic setpoint .................... 59
11.3.89
Setpoint adjustment - Resetting the manual adjustment for change of operating mode ....................... 60
11.3.90
Setpoint adjustment - Resetting the manual adjustment via object ....................................................... 60
11.3.91
Setpoint adjustment - Permanent storage of on-site operation ............................................................. 60
11.3.92
Temperature reading - Inputs of temperature reading........................................................................... 60
11.3.93
Temperature reading - Inputs of weighted temperature reading ........................................................... 61
11.3.94
Temperature reading - Weighting of internal measurement (0 to 100%)............................................... 61
11.3.95
Temperature reading - Weighting of external measurement (0 to 100%) .............................................. 61
11.3.96
Temperature reading - Weighting of external measurement 2 (0 to 100%) ........................................... 61
11.3.97
Temperature reading - Cyclic sending of the actual temperature (min)................................................. 62
11.3.98
Temperature reading - Difference of value for sending the actual temperature (x 0.1°C) ..................... 62
11.3.99
Temperature reading - Adjustment value for internal temperature measurement (x 0.1°C) .................. 62
11.3.100
Temperature reading - Monitoring time for temperature reading (0 = no monitoring) (min) .................. 62
11.3.101
Temperature reading — Operating mode for fault ................................................................................ 63
11.3.102
Temperature reading - Control value for fault (0 - 255) ......................................................................... 63
11.3.103
Alarm functions ..................................................................................................................................... 63
11.3.104
Alarm functions - Condensate water alarm ........................................................................................... 63
11.3.105
Alarm functions — Dew point alarm ...................................................................................................... 64
11.3.106
Alarm functions - Frost alarm temperature for HVAC and RHCC status (°C) ........................................ 64
11.3.107
Alarm functions - Heat alarm temperature for RHCC status (°C) .......................................................... 64
11.3.108
Fan coil settings - Fan speed levels ...................................................................................................... 64
11.3.109
Fan coil settings - Fan speed levels Number of fan speed levels ......................................................... 64
11.3.110
Fan coil settings - Fan speed levels - Format of the level output .......................................................... 65
11.3.111
Fan coil settings - Fan speed levels - Level output ............................................................................... 65
