ABB IRB 6600 - 175/2.8 type B Product Manual Download

Page: 54 / 533

2 Installation and commissioning

2.3. Securing the robot

3HAC023082-001 Revision: E

rig

t 200

200

8 ABB. All righ

ts reser

ed.

Action

Note

1. Mount the transport support lower end to the

robot using the recommended screw joint, (A)
in figure.

Do not tightening the screw.

See attachment point for the specific
robot in section

Transport position with

a transport support

2. Jog the robot into a position as near above as

possible to the recommended transport
position for the specific robot. specified in
section

Transport position with a transport

support

CAUTION!

Do not try to jog the robot to the exact
position (max distance 1mm).

3. Use the brake release for axis 3 to reach the

final resting position on the transport support,
see section

Manually releasing the brakes

See attachment point for the specific
robot in section

Transport position with

a transport support

4. Tightening all the attachment screws (A) and

(B) in figure with the brake release for axis 3
still activated starting with the lower end
attachment screw.

CAUTION!

Do not attempt to tightening any
attachment screw without first release
the brakes, this can seriously damage
the robot.

5. Use the brake release for axis 5 and 6 to

reach the final resting position for the tool, see
section

Manually releasing the brakes

Continued

Summary of Contents for IRB 6600 - 175/2.8 type B






















































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 6600 - 175/2.8 type B

Reviews:

Related manuals for IRB 6600 - 175/2.8 type B

Brands by name

Popular brands

ABB IRB 6600 - 175/2.8 type B, Product Manual

Search results

Summary of Contents for IRB 6600 - 175/2.8 type B

Reviews:

Related manuals for IRB 6600 - 175/2.8 type B

Brands by name

Popular brands