ABB IRB 6620 Product Manual Download

Page: 231 / 360

Note

Action

CAUTION

The lower arm weighs 75 kg
(gearboxes axes 2-3 ex-
cluded)!

Shown in the figure

Location of lower arm on page 228

Remove the attachment
screws and washers securing
the lower arm to gearbox axis
2.

Remove the lower arm.

Refitting

The procedure below details how to refit the lower arm.

Note

Action

Secure the lower arm with a roundsling and lift
it to its mounting position.

CAUTION

The lower arm weighs 75 kg (gearboxes axes
2-3 excluded)!

Make sure the o-ring is fitted to the gearbox.

Lightly lubricate the o-ring with grease.

Fit guiding pins in two of the holes in gearbox
axis 2.

Lift the lower arm on to the guiding pins.

Shown in the figure

Location of lower

arm on page 228

Refit the attachment screws and washers secur-
ing the lower arm to gearbox axis 2.

M16x50, quality 12.9 gleitmo (16 pcs).
Tightening torque: 300 Nm.

Remove the guiding pins.

Secure the upper arm with a roundsling and lift
it to its mounting position.

Detailed in the section

Replacement

of the upper arm on page 222

Refit the upper arm.

Detailed in the section

Replacement

of cable harness, upper end on
page 192

Refit the cable harness axes 3-6.

Pendulum Calibration is described in

Operating manual - Calibration Pendu-
lum

, enclosed with the calibration

tools.

Recalibrate the robot.

Axis Calibration is described in

Calib-

rating with Axis Calibration method on
page 319

General calibration information is in-
cluded in section

Calibration on

page 305

Continues on next page

Product manual - IRB 6620

231

3HAC027151-001 Revision: T

4 Repair

4.4.4 Replacement of lower arm

Continued

Summary of Contents for IRB 6620








































































































































































































































































































































































Search results

Summary of Contents for IRB 6620

Reviews:

Related manuals for IRB 6620

Brands by name

Popular brands

ABB IRB 6620, Product Manual

Search results

Summary of Contents for IRB 6620

Reviews:

Related manuals for IRB 6620

Brands by name

Popular brands