manualshive.com logo in svg

ABB IRB 920, Product Manual

The ABB IRB 920 product is a versatile and advanced robotic arm designed for various industrial applications. With its exceptional precision and efficiency, it ensures optimized performance. For detailed insights, download the free product specification manual from 88.208.23.73:8080, offering step-by-step instructions for seamless integration and operation.

Share
Download
background image

5.2 General procedures

5.2.1 Performing a leak-down test

When to perform a leak-down test

After refitting any motor and gearbox, the integrity of all seals enclosing the gearbox
oil must be tested. This is done in a leak-down test.

Required equipment

Note

Article number

Equipment, etc.

-

Leak-down tester

-

Leak detection spray

Performing a leak-down test

Note

Action

Finish the refitting procedure of the motor or gear in
question.

1

Remove the upper oil plug on the gear and replace
it with the leak-down tester.

2

Regulators, which are included in the leak-down test,
may be required.

Correct value:

Use caution, apply compressed air and raise the
pressure with the knob until the correct value is
shown on the manometer.

CAUTION

The pressure must under no circumstance be higher
than 0.25 bar (20-25 kPa). Also during the time when
the pressure is raised.

3

0.2-0.25 bar (20-25 kPa)

Disconnect the compressed air supply.

4

If the compressed air is signific-
antly colder or warmer than the
gearbox to be tested, a slight
pressure increase or decrease
may occur. This is quite normal.

Wait for approximately 8-10 minutes and make sure
that no pressure loss occurs.

5

If any pressure drop occurred, then localize the leak
as described in step

7

.

6

If no pressure drop occurred, then remove the leak-
down tester and refit the oil plug. The test is complete.

Spray any suspected leak areas with the leak detec-
tion spray. Bubbles indicate a leak.

7

When the leak has been localized, take the necessary
measures to correct the leak.

8

112

Product manual - IRB 920

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

5 Repair

5.2.1 Performing a leak-down test

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

DH CGC-80 Short Manual preview
CGC-80
Brand: DH Pages: 22
K-Team Koala 2.5 User Manual preview
Koala 2.5
Brand: K-Team Pages: 53
DAGU Doodle Bot Manual preview
Doodle Bot
Brand: DAGU Pages: 12
Uctronics WIFI Smart Robot Car Kit User Manual preview
WIFI Smart Robot Car Kit
Brand: Uctronics Pages: 52
CRS A255 User Manual preview
A255
Brand: CRS Pages: 80
Same Toy 2011UT User Manual preview
2011UT
Brand: Same Toy Pages: 56
YASKAWA YR-1-06VX50-A00 Operating And Maintenance Manual preview
YR-1-06VX50-A00
Brand: YASKAWA Pages: 86
Aisoy Robotics KiK User Manual preview
KiK
Brand: Aisoy Robotics Pages: 18
DrRobot Jaguar 4x4 User Manual preview
Jaguar 4x4
Brand: DrRobot Pages: 24
Arduino TA0136 User Manual preview
TA0136
Brand: Arduino Pages: 32
Tinkerbots Advanced Robotics Set Manual preview
Advanced Robotics Set
Brand: Tinkerbots Pages: 60

Brands by name

Popular brands

Load more brands