ABB IRB 920 Product Manual Download | Manualshive

Page: 31 / 1008

background image

Elimination/Action

Description

Warning

Make sure that protective gear
like goggles and gloves are al-
ways worn.

When working with lubricants
there is a risk of an allergic reac-
tion.

Allergic reaction

Open the plug carefully and keep
away from the opening. Do not
overfill the gearbox when filling.

When opening the oil or grease
plug, there may be pressure
present in the gearbox, causing
lubricant to spray from the
opening.

Possible pressure
build-up in gearbox

Make sure not to overfill the
gearbox when filling it with oil or
grease.

Overfilling of gearbox lubricant
can lead to internal over-pres-
sure inside the gearbox which in
turn may:

•

damage seals and gas-
kets

•

completely press out
seals and gaskets

•

prevent the robot from
moving freely.

Do not overfill

After filling, verify that the level
is correct.

After filling, verify that the level
is correct.

The specified amount of oil or
grease is based on the total
volume of the gearbox. When
changing the lubricant, the
amount refilled may differ from
the specified amount, depending
on how much has previously
been drained from the gearbox.

Specified amount de-
pends on drained
volume

For lifetime reasons always drain
as much oil as possible from the
gearbox. The magnetic oil plugs
will gather residual metal chips.

Contaminated oil in
gearboxes

Hazards related to batteries

Under rated conditions, the electrode materials and liquid electrolyte in the batteries
are sealed and not exposed to the outside.

There is a hazard in case of abuse (mechanical, thermal, electrical) which leads
to the activation of safety valves and/or the rupture of the battery container. As a
result under certain circumstances, electrolyte leakage, electrode materials reaction
with moisture/water or battery vent/explosion/fire may follow.

Do not short circuit, recharge, puncture, incinerate, crush, immerse, force discharge
or expose to temperatures above the declared operating temperature range of the
product. Risk of fire or explosion.

Operating temperatures are listed in

Operating conditions, robot on page 40

.

See safety instructions for the batteries in

Material/product safety data

sheet - Battery pack

(

3HAC043118-001

).

Continues on next page

Product manual - IRB 920

31

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

1 Safety

1.6.1 Safety during maintenance and repair

Continued

«
...
29
30
31
32
33
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

RobotEye RE01 Imaging

Brand: Ocular Pages: 27

OMNIS Sample Robot Pick&Place

Brand: Metrohm Pages: 103

Brand: EFORT Pages: 55

Brand: EFORT Pages: 305

Brand: GreyRobotics Pages: 21

Brand: OSOYOO Pages: 86

Brand: Paddle Palace Pages: 14

Brand: ABB Pages: 56

Brand: Joy-it Pages: 6

Brand: Plymovent Pages: 12

Brand: Plymovent Pages: 14

Brand: Innovative Pages: 92

Brand: Eddyfi Technologies Pages: 30

Inuktun VT150 Vertical Crawler

Brand: Eddyfi Technologies Pages: 31

Brand: Eddyfi Technologies Pages: 29

Brand: Eddyfi Technologies Pages: 38

Brand: Empath Interactive Pages: 11

Brand: Denso Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands