ABB IRB 920 Product Manual Download | Manualshive

Page: 948 / 1008

background image

6.1.3 When to calibrate

When to calibrate

The system must be calibrated if any of the following situations occur.

The resolver values are changed

If resolver values are changed, the robot must be re-calibrated using the calibration
methods supplied by ABB. Calibrate the robot carefully with standard calibration,
according to information in this manual.

If the robot has

absolute accuracy

calibration, it is also recommended, but not

always necessary to calibrate for new absolute accuracy.

The resolver values will change when parts affecting the calibration position are
replaced on the robot, for example motors or parts of the transmission.

The revolution counter memory is lost

If the revolution counter memory is lost, the counters must be updated. See

Updating revolution counters on page 952

. This will occur when:

•

The battery is discharged

•

A resolver error occurs

•

The signal between a resolver and measurement board is interrupted

•

A robot axis is moved with the control system disconnected

The revolution counters must also be updated after the robot and controller are
connected at the first installation.

The robot is rebuilt

If the robot is rebuilt, for example, after a crash or when the reach ability of a robot
is changed, it needs to be re-calibrated for new resolver values.

If the robot has

absolute accuracy

calibration, it needs to be calibrated for new

absolute accuracy.

948

Product manual - IRB 920

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

6 Calibration

6.1.3 When to calibrate

«
...
946
947
948
949
950
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

Brand: Magic-Q Pages: 16

TI-Innovator Rover

Brand: Texas Instruments Pages: 20

Brand: Stem Pages: 20

Brand: RS Barcelona Pages: 8

Brand: rozum robotics Pages: 56

Boe-Bot Tank Treads

Brand: Parallax Pages: 10

Brand: ABB Pages: 118

Brand: XYZrobot Pages: 32

Brand: AgileX Pages: 24

Brand: Vivato Pages: 8

Brand: Trossen Robotics Pages: 26

App Enabled Droid BB-8

Brand: Sphero Pages: 7

Brand: RD9 Solutions Pages: 15

Brand: RD9 Solutions Pages: 14

Dali the PhotoBot

Brand: Phomatix Pages: 5

Fischertechnik Bionic Robots

Brand: FISCHER Pages: 64

Brand: Cebekit Pages: 3

Brand: Cebekit Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands