ABB IRB 920 Product Manual Download | Manualshive

Page: 977 / 1008

background image

7 Troubleshooting

7.1 Introduction to troubleshooting

Introduction

The product manual and the circuit diagram contains information that can be good
when troubleshooting.

For OmniCore, all event logs from the software can be seen on the FlexPendant,
or in

Technical reference manual - Event logs for RobotWare 7

.

Make sure to read through the section

Safety on page 15

before starting.

Troubleshooting strategies

1 Isolate the fault to pinpoint the cause of the problem from consequential

problems.

2 Divide the fault chain in two.

3 Check communication parameters and cables.

4 Check that the software version is compatible with the hardware.

Work systematically

1 Take a look around to make sure that all screws, connectors, and cables are

secured, and that the robot and other parts are clean, not damaged, and
correctly fitted.

2 Replace one thing at a time.

3 Do not replace units randomly.

4 Make sure that there are no loose screws, turnings, or other unexpected

parts remaining after work has been performed.

5 When the work is completed, verify that the safety functions are working as

intended.

Keep a track of history

•

Make a historical fault log to keep track of problems over time.

•

Consult those working with the robot when the problem occurred.

Basic scenarios

What to look for during troubleshooting depends on when the fault occurred. Was
the robot recently installed or was it recently repaired? The following table gives
hints on what to look for in specific situations.

Check:

•

the configuration files

•

connectors

•

options and their configuration

•

changes in the robot working space/movements.

The robot has recently
been installed

Continues on next page

Product manual - IRB 920

977

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

7 Troubleshooting

7.1 Introduction to troubleshooting

«
...
975
976
977
978
979
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

Heavy Payload Series

Brand: TM Robot Pages: 87

Brand: SIASUN Pages: 87

Brand: Zimmer Pages: 52

Solar Power Project Pack

Brand: Mindsets Pages: 4

Brand: Sol-Expert group Pages: 11

Brand: Doosan Pages: 190

Brand: Vecna Healthcare Pages: 4

Brand: ABB Pages: 56

Brand: ROBOTIQ Pages: 99

Interbotix PhantomX

Brand: Trossen Robotics Pages: 3

Brand: Skyrocket Pages: 2

Brand: Skyrocket Pages: 4

Brand: Susteen Pages: 37

Brand: RealMan Pages: 85

Brand: RealMan Pages: 84

Brand: Otto Pages: 27

Brand: MantaroBot Pages: 14

Brand: Kuka Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands