ABB IRB 920 Product Manual Download | Manualshive

Page: 39 / 1008

background image

Bending moment in any direction in Plane XY

T

xy

Torsional moment around Axis Z

T

z

The table shows the various forces and torques working on the robot during different
kinds of operation.

Note

These forces and torques are extreme values that are rarely encountered during
operation. The values also never reach their maximum at the same time!

WARNING

The robot installation is restricted to the mounting options given in following load
table(s).

Floor mounted

Maximum load (emergency stop)

Endurance load (in operation)

Force

±1500 N

±550 N

Force xy

±650 N

±550 N

Force z

±500 Nm

±330 Nm

Torque xy

±900 Nm

±150 Nm

Torque z

Requirements, foundation

The table shows the requirements for the foundation where the weight of the
installed robot is included:

Note

Value

Requirement

Flat foundations give better repeatability of the
resolver calibration compared to original settings
on delivery from ABB.

0.1/500 mm

Flatness of foundation
surface

The value for levelness aims at the circumstance
of the anchoring points in the robot base.
In order to compensate for an uneven surface,
the robot can be recalibrated during installation.
If resolver/encoder calibration is changed this
will influence the absolute accuracy.

0°

Maximum tilt

The value is recommended for optimal perform-
ance.

22 Hz

Note

It may affect the
manipulator life-
time to have a
lower resonance
frequency than
recommended.

Minimum resonance
frequency

Due to foundation stiffness, consider robot mass
including equipment.

i

For information about compensating for founda-
tion flexibility, see

Application manual - Control-

ler software OmniCore

, section

Motion Process

Mode

.

Continues on next page

Product manual - IRB 920

39

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

2 Manipulator description

2.2 Technical data

Continued

«
...
37
38
39
40
41
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

Brand: WEISS ROBOTICS Pages: 69

Brand: RoboBuilder Pages: 89

Brand: Panasonic Pages: 38

OpenManipulator-X

Brand: Robotis Pages: 12

Brand: Robotnik Pages: 29

2-Finger Adaptive Robot Gripper - 200

Brand: ROBOTIQ Pages: 113

Brand: Cebekit Pages: 37

Brand: Cebekit Pages: 39

Brand: Marvelmind Pages: 263

Brand: WowWee Pages: 4

Brand: WowWee Pages: 12

Lucas the Robot

Brand: Totem Pages: 44

Brand: OhmniLabs Pages: 2

PATROL XT380972

Brand: Xtrem Bots Pages: 52

TI-Innovator Hub

Brand: Texas Instruments Pages: 12

Brand: Shini Pages: 49

Brand: MISA Pages: 24

Brand: kowatec Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands