ABB IRB 920 Product Manual Download | Manualshive

Page: 955 / 1008

background image

Step 2 - Updating the revolution counter with the FlexPendant

Note

Revolution counters of axes 3 and 4 must be updated together.

Use this procedure to update the revolution counter with the FlexPendant
(OmniCore).

Action

On the start screen, tap

Calibrate

.

1

Select

Calibration

from the menu.

2

The

Mechanical Units

page displays a list of available mechanical units.

Note

This step is required only if you are not already in the

Mechanical Unit

page when

you open

Calibrate

.

Note

The

Mechanical Unit

page is displayed only if there are more than one mechanical

unit available. Otherwise, the calibration summary page for the available mechanical
unit is displayed.

Select the mechanical unit for which revolution counter need to be updated.

3

The calibration summary page for the selected mechanical unit is displayed.

4

Calibration method used at factory for each axis is shown, as well as calibration
method used during last field calibration.

Tap

Calibration Methods

on the right pane.

5

The calibration options are displayed.

Tap

Revolution Counters

.

6

In the

Selection

column select the axes for which revolution counters need to be up-

dated.

7

Tap

Update

.

A dialog box is displayed, warning that the updating operation cannot be undone:

•

Tap

Update

to proceed with updating the revolution counters.

•

Tap

Cancel

to cancel updating the revolution counters.

Tapping

Update

and a confirmation window is displayed.

8

Tap

OK

.

9

The revolution counter for the selected axes is updated.

CAUTION

If a revolution counter is incorrectly updated, it will cause incorrect manipulator posi-
tioning, which in turn may cause damage or injury!
Check the synchronization position very carefully after each update. See

the synchronization position on page 976

.

10

Product manual - IRB 920

955

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

6 Calibration

6.3.1 Updating revolution counters on OmniCore robots

Continued

«
...
953
954
955
956
957
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

Robo 2.0 Lucky Lottery

Brand: Artec Pages: 10

2 DOF Planar Robot

Brand: Quanser Pages: 17

Brand: Velleman Pages: 11

Brand: Evil Mad Scientist Pages: 60

Tosy Disco Robo

Brand: LOGICOM Pages: 26

Brand: LOGICOM Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands