ABB IRB 920 Product Manual Download | Manualshive

Page: 980 / 1008

background image

7.3 Mechanical noise or dissonance

Description

Mechanical noise or dissonance that has not been observed before can indicate
problems in bearings, motors, gearboxes, or similar. Be observant of changes over
time.

A faulty bearing often emits scraping, grinding, or clicking noises shortly before
failing.

A humming resonance sound can occur without being an error. Mechanical
resonance sound is a physical phenomenon in mechanical structures. It has no
impact on product performance or lifetime. Adjusting the robot movement speed
out of the range that causes the resonance will eliminate the sound.

Consequences

Failing bearings cause the path accuracy to become inconsistent, and in severe
cases, the joint can seize completely.

Possible causes

The symptom can be caused by:

•

Worn bearings.

•

Contaminations have entered the bearing grooves.

•

Loss of lubrication in bearings.

•

Loss of lubrication in ball screw.

•

Loose heat sinks, fans, or metal parts.

If the noise is emitted from a gearbox, the following can also apply:

•

Overheating.

Recommended actions

The following actions are recommended:

Information

Action

CAUTION

Allow hot parts to cool down.

1

Verify that the service is done according to
the maintenance schedule.

2

If a bearing is emitting the noise, determine
which one and make sure that it has suffi-
cient lubrication.

3

If possible, disassemble the joint and meas-
ure the clearance.

4

Bearings inside motors are not to be re-
placed individually, but the complete motor
is replaced.

5

Make sure the bearings are fitted correctly.

6

Continues on next page

980

Product manual - IRB 920

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

7 Troubleshooting

7.3 Mechanical noise or dissonance

«
...
978
979
980
981
982
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

Brand: MakerBot Pages: 24

Brand: Supereyes Pages: 15

COMPETITION 740

Brand: Cornilleau Pages: 7

Brand: labrobotics Pages: 30

IRB 7600 - 500/2.55

Brand: ABB Pages: 482

Brand: Vstone Pages: 11

Brand: Staubli Pages: 42

Brand: Steren Pages: 42

LEGO MINDSTORMS NXT ZOO!

Brand: Rhodes Pages: 28

Brand: ROKAE Pages: 53

Brand: ROKAE Pages: 53

FIREBIRD V ATMEGA 2560

Brand: NEX ROBOTICS Pages: 121

Brand: Mayer Pages: 70

Brand: Blue point Pages: 42

Brand: AgileX Pages: 22

Brand: AgileX Pages: 27

Brand: Arduino Pages: 32

Brand: Universal Robots Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands