ABB IRB 920 Product Manual Download | Manualshive

Page: 983 / 1008

background image

7.5 Motor temperature too high

Description

The robot stops and the motor temperature for joint arg is too high.

Consequences

It is not possible to continue until the motor has cooled down. The system goes to
Motors Off.

Possible causes

The symptom can be caused by:

•

The values for payload and arm load are not consistent with the actual ones.

•

The value for ambient temperature setting in the controller is not consistent
with the actual operating temperature environment.

•

The user program may contain too much high acceleration and deceleration
of the joint.

•

Gravity torque or external forces for the joint can also be too high.

Recommended actions

The following actions are recommended:

Information

Action

CAUTION

Allow hot parts to cool down.

1

Verify that the values for payload and arm
load are set correctly.

2

Verify that the value for ambient temperature
setting in the controller is consistent with the
actual operating temperature environment.

3

The ways could be but not limited to op-
timizing robot movement cycle, adjusting
acc, dec as well as external force, adding
wait time, and introducing alternative
path/RAPID, etc.

Rewrite the user program to reduce the mo-
tor utilization.

4

Product manual - IRB 920

983

3HAC075721-001 Revision: C

© Copyright 2022 ABB. All rights reserved.

7 Troubleshooting

7.5 Motor temperature too high

«
...
981
982
983
984
985
...
»

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 920

SPIN MASTER 19206

Brand: Meccano Pages: 83

Brand: Buind Pages: 8

Brand: DFRobot Pages: 10

Brand: EFORT Pages: 46

Brand: Sony Pages: 2

AIBO Speed Boarder

Brand: Sony Pages: 60

Brand: Sony Pages: 65

AIBO Pal ERS-31L

Brand: Sony Pages: 84

Brand: Sony Pages: 106

Brand: Sony Pages: 115

AIBO LIFE ERF-210AW01

Brand: Sony Pages: 164

Brand: Sony Pages: 208

Brand: Sony Pages: 234

Brand: SuperDroid Robots Pages: 6

HEXBUG BATTLE GROUND BUNKER 409-5121

Brand: Innovation First Pages: 2

Brand: YASKAWA Pages: 92

Brand: Hiwin Pages: 85

Brand: ABB Pages: 398

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands