ABB IRB 930 Product Manual Download | Manualshive

Page: 568 / 606

background image

Periodic check of the calibration tool

If including the calibration tool in a local periodic check system, the following
measures should be checked.

•

Outer diameter within Ø12g4 mm, Ø8g4 mm or Ø6g5 mm (depending on
calibration tool size).

•

Straightness within 0.005 mm.

xx1500000951

Outer diameter

A

Identifying the calibrating tools

It is possible to make the calibration tool identifiable with, for example, an RFID
chip. The procedure of how to install an RFID chip is described below.

Note

The tool identifier is NOT delivered from ABB, it is a customized solution.

Note

Action

It is possible to use any RFID solution, with the
correct dimensions. ABB has verifed function on
some suppliers fulfilling the requirements of NFC
compatible devices (13.56 Mhz) according to ISO
14443 or ISO 15693.

Note

The maximum dimensions on the RFID chip must
not exceed Ø7.9 mm x 8.0 mm, Ø5.9 mm x 8.0
mm or Ø3.9 mm x 8.0 mm (depending on calibra-
tion tool size).

1

There is a cavity on one end of the calibration tool
in which the RFID chip can be installed.

2

Install the RFID chip according to supplier instruc-
tions.
Install the chip in flush with the tool end.

568

Product manual - IRB 930

3HAC086009-001 Revision: A

© Copyright 2023 ABB. All rights reserved.

6 Calibration

6.4.2 Calibration tools for Axis Calibration

Continued

«
...
566
567
568
569
570
...
»

Summary of Contents for IRB 930































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 930

Brand: ST Robotics Pages: 27

Brand: Kuka Pages: 109

Brand: MechRC Pages: 27

Brand: Rethink Robotics Pages: 220

Brand: Paddle Palace Pages: 13

Brand: YASKAWA Pages: 36

Brand: Velleman Pages: 13

Brand: Trossen Robotics Pages: 26

Brand: Singer Instruments Pages: 30

Brand: Sportime Pages: 6

Brand: Sportime Pages: 6

Brand: Strawbees Pages: 20

Brand: Plum Geek Robotics Pages: 64

Brand: McConnel Pages: 72

Robotics Competition Turning Point

Brand: Vex Pages: 44

Brand: Paddle Palace Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands