ABB OmniCore V250XT Product Manual Download

Page: 373 / 456

7.2.10 Controller is overheated

Required test equipment

Equipment needed for troubleshooting:

Note

Equipment

Multimeter

Insulating gloves

3HAC074000-008

Circuit diagram - OmniCore V250XT

Preparations

Action

Make sure that the controller is switched on.

Wait 30 s - 1 min to enable start-up sequence.

Check the FlexPendant for errors and warnings.

DANGER

Troubleshooting on the controller while powered on must be performed by personnel
trained by ABB or by ABB field engineers.

Recommended working procedure

If the controller seems to be overheated, use this procedure to troubleshoot what
might cause the problem.

Detailed working procedure

Note

Action

Replace malfunctioning fans, see

Replacing the standard fans on
page 182

Check that the standard fans are working.

Replace malfunctioning fans, see

Replacing the internal fan on
page 186

Check that the internal fan is working.

Replace malfunctioning fans, see

Replacing the power unit fan on
page 198

Check that the power unit fan is working.

If air filters are not clean, see

Cleaning air filter on page 157

Inspect the air filters to make sure they are clean.

If air filters need to be replaced,
see

Replacing the air filter on

page 298

See

Troubleshooting the power

unit on page 382

and

Troubleshoot-

ing the drive unit on page 376

If the problem remains, troubleshoot the power
unit and/or the drive unit.

Product manual - OmniCore V250XT

373

3HAC073447-001 Revision: B

7 Troubleshooting

7.2.10 Controller is overheated

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands