ABB OmniCore V250XT Product Manual Download | Manualshive

Page: 409 / 456

background image

Action

Test

Use a multimeter and insulating gloves.

Measure the input voltage to
the robot signal exchange
proxy.

Tip

For more details, see

Circuit

diagram - OmniCore V250XT

.

3

The input voltage should be 24 V.
Make sure that connector X1 is connected properly
on both ends.

•

If the input voltage is normal, proceed with
step

.

•

If the input voltage is abnormal, proceed with
step

.

•

If the connection is OK, troubleshoot the
power unit. See

Troubleshooting the power

unit on page 382

.

•

If there is a problem with the connection, re-
pair the connection and start over.

Check connection to the
power unit.

4

Use a multimeter and insulating gloves.

Measure the 24 V DC outputs
voltage.

5

The output voltage should be 24 V.
Make sure that connectors X2, X3, X4, X5, X17 and
X19 are connected properly on both ends.

•

If the output voltage is normal, proceed with
step

.

•

If the output voltage is abnormal, proceed with
step

.

The indicator LEDs are labelled AS1, AS2, ES1, ES2.

Check the indicator LEDs
AS1, AS2, ES1, ES2.

6

If the LEDs LED_AS1, AS2, ES1, ES2 are:

•

On (solid green), the robot signal exchange
proxy works well.

•

Off, either the robot signal exchange proxy is
faulty or it does not have sufficient input
voltage. Proceed with step

.

If the customer interface connectors are not properly
connected to X14 and X15, the signals to and from
the robot signal exchange proxy will be interpreted
incorrectly.

•

If the connection is OK, proceed with step

.

•

If there is a problem with the connection, re-
pair the connection and go to step

Check that the customer inter-
face connectors are connec-
ted to X14 and X15.

Tip

For more details, see

Circuit

diagram - OmniCore V250XT

.

7

Use a multimeter and insulating gloves.

Check external safety ac-
cessories.

8

Measure the continuity in the connector. If there is
resistance, troubleshoot the external equipment.

Use a multimeter and insulating gloves.

Measure the AC OK signal.

9

The AC OK should be 0 V.
Make sure that connector X10 is connected properly
on both ends.

•

If the AC OK signal is 24 V, see

Troubleshooting the power unit on page 382

•

If the AC OK signal is 0 V, proceed with step

How to replace the unit is detailed in

robot signal exchange proxy on page 202

The robot signal exchange
proxy may be faulty, replace
it and verify that the fault has
been fixed.

10

Product manual - OmniCore V250XT

409

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

7 Troubleshooting

7.3.11 Troubleshooting the robot signal exchange proxy

Continued

«
...
407
408
409
410
411
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: Pololu Pages: 97

Brand: jbc Pages: 12

Brand: SuperDroid Robots Pages: 9

Brand: YASKAWA Pages: 64

Brand: YASKAWA Pages: 96

Brand: ABB Pages: 40

IRB 6640 - 180/2.55

Brand: ABB Pages: 443

Brand: ABB Pages: 640

Brand: Eddyfi Technologies Pages: 13

INUKTUN VERSATRAX 100

Brand: Eddyfi Technologies Pages: 41

Brand: Blue Robotics Pages: 6

Brand: Botzees Pages: 16

Brand: ROBOTIQ Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands