ABB OmniCore V250XT Product Manual Download | Manualshive

Page: 415 / 456

background image

8.5 Screw joints

General

This section details how to tighten the various types of screw joints on the controller.

The instructions and torque values are valid for screw joints comprised of metallic
materials and do

not

apply to soft or brittle materials.

Tightening torque

Before tightening any screw, note the following:

•

Determine whether a standard tightening torque or special torque is to be
applied. The standard torques are specified in the tables below. Any special
torques are specified in the Repair, Maintenance or Installation procedure
description. Any special torque specified overrides the standard value.

•

Use the

correct tightening torque

for each type of screw joint.

•

Only use

correctly calibrated

torque keys.

•

Always

tighten the joint by hand,

and never use pneumatical tools.

•

Use the

correct tightening technique

, i.e.

do not

jerk. Tighten the screw in a

slow, flowing motion.

•

Maximum allowed total deviation from the specified value is

10%

!

The table below specifies the recommended standard tightening torque for

oil-lubricated screws

with

slotted or cross-recess heads.

Tightening torque (Nm)
Class 4.8, oil-lubricated

Dimension

0.25

M2.5

0.5

M3

1.2

M4

2.5

M5

5.0

M6

Product manual - OmniCore V250XT

415

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

8 Reference information

8.5 Screw joints

«
...
413
414
415
416
417
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: ABB Pages: 64

Brand: ABB Pages: 18

Brand: ABB Pages: 90

Brand: Omron Pages: 10

Brand: Motoman Pages: 25

Brand: K-Team Pages: 20

Starter Robot Kit

Brand: Makeblock Pages: 14

Brand: rozum robotics Pages: 32

Brand: Stiga Pages: 10

Brand: SunFounder Pages: 67

Brand: Staubli Pages: 42

Brand: BOOCAX Pages: 15

BKS-UVRobot-200

Brand: BOOCAX Pages: 23

Brand: BOOCAX Pages: 25

Brand: BOOCAX Pages: 26

Brand: BOOCAX Pages: 28

Brand: BOOCAX Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands