ABB OmniCore V250XT Product Manual Download

Page: 168 / 456

4.5.3 Function test of three-position enabling device

Performing the function test

Note

Action

Start the robot system and turn the mode
switch to manual mode.

This test is passed if the event message

10011 Motors ON state

appears in the

event log.

Press the three-position enabling device
to the middle position and then hold the
enabling device in this position.

If the event message

10011 Motors ON

state

does not appear, or if the event

message

20224 Enabling device conflict

appears in the event log, then the test has
failed and the root cause of the failure must
be found.

This test is passed if the event message

10012 safety guard stop state

appears in

the event log.

While still holding the three-position en-
abling device pressed, press the enabling
device harder to the enable the device's
third position.

If the event message

10012 Safety guard

stop state

does not appear, or if the event

message

20224 Enabling device conflict

appears in the event log, then the test has
failed and the root cause of the failure must
be found.

168

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

4 Maintenance

4.5.3 Function test of three-position enabling device

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands